T1000S Controller Specifications

T-1000S LED controller is one of the most common LED controllers available today for programming pixel LEDs due to it's low prize and features .

Here are the general specifications of T-1000S controller  -
Input voltage    : 5V-24V

Power               : 1W

Dimensions      : 6.30 in x 2.95 in x 0.91 in (16.0 cm x 7.5 cm x 2.3 cm)

Weight              : 230 g

MAX programs : 16

MAX LEDs        : 2048Program 

method             : Off-line(SD Card)

It can control single line (Data line only ) and double line (Data and Clock line)  LED drive chips .It Supports 32- 256 Gray and software Gamma correction. Single-port output, can support maximum of 2048 LEDs .control.You can also use several units to extend the number of ports(eg - with two controllers networked you can control up to 4096 LEDs.
Selecting the Controller in the Software
In order to program T-1000S controller it requires LED Edit 2012 - 2019 or later versions . Download LED Edit software from below .

LedEdit 2014_V2.4.rar https://gplinks.in/7aQwt3x

2018+LedEdit-K_v3.53.1.rar https://gplinks.in/gnpGeJ

2019 LedEdit-K_v4.3_setup.rar https://gplinks.in/fHM0

LED edit 2019K V.5.1 LED edit 2019K V.4.7 LED edit 2019K V.4.6

Download Link

Download Link

https://pixelled98.blogspot.com/2020/03/pixel-led-2019-latest-version-softwares.html?m=1 #LEDedit2019K

how to use led edit 2019K, #electronics, pixel led programming, pixel led, how to programme led edit 2019, pixel led programme, led edit 2019 tutorial, pixel programming, how to add pixel programme in sd card, pixel led strip, pixel led #ws2812 strip, 70 amper power supply, highlite power supply, how to programme #t1000s controlller, t1000 controller

2012 T-1000S Operating manual

1、T-1000S System features 

 1、32—256 Gray，Support software Gamma correction。

 2、Support the rules and special-shaped handle.

 3、Single-port output，can support 2048 lights。

 4、Off-line(SD Card) control, play back content stored in the SD card. 

5、T-1000S store a maximum of 16 programs，copy multiple files to the SD card in order, after formatting the SD card as “FAT” format. 

6、The program must be named in orders .

Ex. ：00_1.led, 01_1.led, 02_1.led. 

7、Compatible with single line or double line chips.

NOTE：1. When T-1000S controller less than 512 pixels the frame rate can reach 30fps. When T-1000S control more than 512 pixels the frame rate will slow down automatically.

2. T-1000S must use the new software LedEdit 2012.

Supported Driver chips  

Capacity
For The T-1000S Controller ,The recommended capacity is between 128MB - 2GB ,Which means you can use 128MB , 256MB, 512MB , 1GB ,2GB SD cards 

TM1803,TM1804,TM1809,TM1812,TM1829,TM1913,TM1914,UCS1903,UCS1903B,
UCS1909B,UCS1912,UCS2903,UCS2909,UCS2912,UCS3903,UCS6909,UCS6912,UCS7009,
UCS5903,UCS8903,UCS512,US2811,WS2821,P9813,P9823,LPD1886,GW6202,GW6201,
GW6202B,GW6204,GW6203,GW623X,TA9909,MBI6021,INK1003,LX10003,LX2003,
LX2006,TLS3100,DMX,SM16711,SM16726,SM16716,LPD6803,LPD8806,LPD1882,LPD6812,
TM1903,TM1904,TM1909,TM1912,,DMXMonochrome,WS2801,WS2803,D7710,QC1109,
TLS3001,TLS3008,APA102,MY9221,BS0815,BS0825,BS0901,HL32,HL1809,HL2803,
RGB,Monochrome,XB001,XB002

.Connection diagram 

1. Multiple T-1000S controllers can be cascaded together and work synchronously.

 2. T-1000S one TTL(SPI) signal and one RS485 signal port output，can control 2048 pixels；

 3. When the chip for LED is single line chip just with data, then it just needs to be connected with DAT and GND of the controller. If the chip for LED is double line chip with DAT and CLK, then it need to be connected with DAT, CLK, and GND of the controller.

4. If you need to use RS485 signal you need to connect controller A with LED A (DMX+), controller B with LED B(DMX-), 

5. When you need to build a new project the controller type for the software is：T-1000-IC model

http://en.led595.com/English/DownLoadDetail/63.htm